MAUN Flat nose Knurled Jaws Plier
MAUN plier 4861-160
MAUN plier 4861-160
Inox wire aisi 302
Glossy finish.
Coil of 10 kg.
To purchase please select desired size and package.
Slotted Mandrel for Emery Paper
Diameter Ø 5 mm.
Inox steel.
Shank 2.35 mm.
Silicone Cone polisher
PEDDINGHAUS Stretching Hammer
LP1670 Round file
Moissanite Tester II
End Brush with 2.35 mm shank
Diameter Ø 5 mm.
White soft goat hair.
Made in Italy.
Black stone to test the karat value of gold
Size: 70 x 50 x 4 mm.
Round Die mm 2.00
Round Bezel Forming Punch Set 5 - 20 mm
Alkaline Batteries AAA
Fine glass bristles replacement
For Pen-Style Fiberglass Brush.
Box of 24 pcs.
Lens Plate for OptiVISOR DA-2
Magnification: 1.50 times.
Focal lenght: 50,80 cm.
Optical glass prismatic lenses: ground and polished to precision optical standards.
Stone Set Ring Enlarger
Stainless steel pickling tank- 3,5 Liters
Equipped with a stainless steel basket.
Heating temperature: 70°C.
Tank Size: mm 240 x 137 x 110H.
Silicone wheel Polisher Ø 22 mm
Green colour, High-gloss Polish.
Speed: 10.000 rpm.
Use only with special screw mandrel, available as an accessory.
Burs Set 4235
Tungsten carbide miller Ø 2,0 mm
Shaft: 3,00 mm.
High wear resistance, for high precision milling without vibrations.
For milling steel, non-ferrous metals, plastics and extremely hard materials.
Ceramic replacement for Ring Stand
To be mounted on base with clamp.
Silent Compressor SIL-AIR 30 D
EDENTA CeraGloss Yellow Ø 25 mm 30001 HP
Diamond polisher for highly efficient polishing of platinum, titanium and ceramics, pressure-free application imperative. Low surface temperature without streak formation.
Yellow colour, for High-gloss polishing.
Mounted on 2.35 mm shank.
Steel Oval Forming Mandrel mm 8x12 - 26x34
You can use this mandrel to easily form bezels, rings and a variety of components.
Lenght 320 mm.
Made in Italy.
Soldering alloy for yellow gold 18 Kt.
Carat: 18 kt.
Color: Yellow.
INDICATIONS FOR SUGGESTED USE
Melting temperature: 960° C.
Bracket temperature: 70° C.
Bracket casting cooling: immediate in lukewarm water (about 40° C).
Annealing: 520° C for 20 minutes followed by rapid cooling in hot water (min. 40 ° C).
Flow temperature: 650° C.
IMPORTANT: the brackets to be used must be vertical and closed on both sides. Open ingot molds cannot be used because the plates thus obtained break upon rolling.
Rolling mill corrugater with base, small type
4 steps: 0,4 - 0,5 - 0,6 - 0,7 mm.
Rollers width: 2,5 mm.
Maximum thickness: 0.3 mm (on gold).
Size: 50 x 250 mm.
Made in Italy.
Silver Sheet Solder - Hard
Bracelet Gauge
LUXOR yellow
UHU Plus 90 Min.
OptiVISOR DA-4
Magnification: 2.00 times
Focal lenght: 25.50 cm.
Optical glass prismatic lenses: ground and polished.
The lens can be easily removed and replaced with one of different magnification.
Can be worn over prescription or safety eyeglasses.
Ceramic Media for tumble vibe.
Triangle shape.
Pack 1 Kg.
Hand Taps Set mm 7.00 (3 Pz.)
Composition: Copper 90% - Tin 10%.
Watch-makers eyepiece 2.8X
Screw Type Mandrel
GLS-50 Liquid rubber for casting
Liquid rubber for casting with a cold cure by poly-condensation.
Before using, add to the rubber 5% of T 30 catalyst.
Pot-life is rather long : 1 hour, while the complete vulcanization takes 18 -20 hours.
To purchase please select desired package.